- CONTOUR SHUTTLE ZONE HOW TO
- CONTOUR SHUTTLE ZONE SERIAL
If you’d hear a strange humming noise during acceleration and deceleration, try to increase the max feed rate and the acceleration speed, and make sure it will not miss steps. Reduce humming sound when accelerating and decelerating
Button 5 - Select Jog Distance (1, 0.1, 0.01, 0.001, or a custom value)Īdjust the keystroke repeat rate to 10 times per second for all Shuttle Zones except the Shuttle Zone 0. Set turn jog dial left (CCW) to jog backward/down, and set turn jog right (CW) to jog forward/up. To work with cnc, configure three buttons to select/deselect X/Y/Z axis, and another one button to switch the distance value. The ShuttleXpress has five programmable buttons, a 10 counts jog dial (the inner wheel), and a 15-position shuttle wheel (the outer wheel) that returns to center when released. You can use the ShuttleXpress jog dial to work with a CNC controller. These are the current keys used in the cnc (from v0.15.3).Ĭtrl + alt + command + x - Select/Deselect X AxisĬtrl + alt + command + y - Select/Deselect Y AxisĬtrl + alt + command + z - Select/Deselect Z AxisĬtrl + alt + command + a - Select/Deselect A AxisĬtrl + alt + command + = or d - Select Jog DistanceĬtrl + alt + command + or f - Jog ForwardĬtrl + alt + shift + 7 - Shuttle Backward (Fastest)Ĭtrl + alt + shift + 6 - Shuttle Backward (Faster)Ĭtrl + alt + shift + 5 - Shuttle Backward (Fast)Ĭtrl + alt + shift + 4 - Shuttle Backward (Normal)Ĭtrl + alt + shift + 3 - Shuttle Backward (Slow)Ĭtrl + alt + shift + 2 - Shuttle Backward (Slower)Ĭtrl + alt + shift + 1 - Shuttle Backward (Slowest)Ĭtrl + alt + command + 1 - Shuttle Forward (Slowest)Ĭtrl + alt + command + 2 - Shuttle Forward (Slower)Ĭtrl + alt + command + 3 - Shuttle Forward (Slow)Ĭtrl + alt + command + 4 - Shuttle Forward (Normal)Ĭtrl + alt + command + 5 - Shuttle Forward (Fast)Ĭtrl + alt + command + 6 - Shuttle Forward (Faster)Ĭtrl + alt + command + 7 - Shuttle Forward (Fastest) 
CONTOUR SHUTTLE ZONE HOW TO
Webcam WidgetĬheckout FAQ to learn how to setup and configure webcam streaming with Raspberry Pi. This widget provides the spindle control. This widget helps you use a touch plate to set your Z zero offset. Once a G-code file is loaded, run the macro for perimeter tracing with respect to current G-code boundary. You can create a macro with the following content: Traverse around the boundary The following variables are supported since cncjs 1.9: This widget can use macros to automate routine tasks. This widget allows you control laser intensity and turn the laser on/off. This widget shows the TinyG state and provides TinyG specific features. This widget shows the Smoothie state and provides Smoothie specific features. Set $10=2 for Grbl v1.1d (or $10=15 for Grbl v0.9) to see planner buffer and receive buffer in queue reports. This widet shows the Grbl state and provides Grbl specific features. This widgets shows the current status of G-code commands.
CONTOUR SHUTTLE ZONE SERIAL
This widget lets you read and write data to the CNC controller connected to a serial port. It includes jog controls, homing, and axis zeroing. This widget lets you establish a connection to a serial port. This widget visualizes a G-code file and simulates the tool path.
0 kommentar(er)
